How to Use Condor XC-Mini Plus Key Cutting Machine

This instruction show you guide on how to use Xhorse Condor XC-Mini plus machine,include cutter installation & uninstallation,clamp installation,clamp instruction..ect.

 

Installation Instruction:

Cluster installation

Installation steps:

1 Put the cutter into the mounting hole and make sure the cutter goes to the limit of top.

2 Use the cutter tightening wrench to clockwise fix the cutter.

How to Use Condor XC-Mini Plus Key Cutting Machine-1

Cutter Uninstallation:

Uninstallation steps:

1) Counter-clockwise unscrew the cutter manually.

2) Take the cutter off when it is loose

How to Use Condor XC-Mini Plus Key Cutting Machine-2

 

Clamp Installation

Installation Step2:

1) Loosening the clamp tightening wrench by turning it counter-clockwise to the left.

2) Select the correct clamp and slide in the clamp to the clamp holder and push it to the limit of left.

3) After the clamp is put in the clamp platform,turn the clamp tightening wrench clockwise for fix it.

How to Use Condor XC-Mini Plus Key Cutting Machine-3

 

Clamps Instruction:

How to Use Condor XC-Mini Plus Key Cutting Machine-4 How to Use Condor XC-Mini Plus Key Cutting Machine-5

 

 

Clamp M2 Sides Selection

How to Use Condor XC-Mini Plus Key Cutting Machine-6

 

6 Clamp M4 Instruction

Clamp M4 for household keys, mainly support standard single and double sided keys,also for

crucifix keys,example as follows:

How to Use Condor XC-Mini Plus Key Cutting Machine-7 How to Use Condor XC-Mini Plus Key Cutting Machine-8

http://www.uobdii.com/wholesale/xhorse-condor-mini-plus.html

Xhorse Condor Mini PLUS key machine Clmap M1/2/3/4 Installation Guide

Here are guides on how to install Jaw m1/2/3/4 on Xhorse Codor Mini Plus:

1)      Loosening the clamp tightening wrench by turning it counter-clockwise to the left.

2)      Select the correct clamp and slide in the clamp to the clamp holder and push it to the limit of left.

3)      After the clamp is put in the clamp platform, turn the clamp tightening wrench clockwise for fix it.

condor-mini-plus-clamp-install

 

So, which jaw/clamp you should use for key cutting?

Look here: clamp – key type

 

Clamp m1: Standard single/double sided key

Clamp m2: 4 Track externa, 2 Track external, 4 Track internal, Channel track, Dimple keys

condor-mini-plus-clamp-m2

Clamp m3: FO21, SX9

condor-mini-plus-clamp-m3

Clamp m4: Sided keys, Crucifix keys

condor-mini-plus-clamp-m4

 

Attachment: Condor mini plus user manual.pdf

Xhorse Condor XC-MINI V4.0.1 (06.16) update and procedure

Here provide Xhorse Condor XC-MINI V4.0.1 features, update link and procedure.

Here provide Xhorse Condor XC-MINI V4.0.1 features, update link and procedure.

 

Xhorse Condor XC-MINI V4.0.1 (2017.06.16) features:

——————————————

+Add universal key decode function

+Add M2-D function

+Add motor sensor testing function

*Modify probe/cutter detection

*Fix machine may crash error problem

*Fix HU49 key decode error

*Fix HU66 cutting speed issue

*Fix BW6 cutting error

*Fix TBE1 cutting error

Notes:

1.New update for both SN KM02/KM03 machines

2.New function: Main Interface-Key Duplication-Universal Type

3.Universal Type support decode/cutting parts of home & vehicle keys

4.Please keep the whole key clean and conductivity good(ensure without dust/oil)

5.For one side key(thickness of whole key usually 1.5mm or 2.00mm) please add a shimsiness card under the key, ensure the whole key thickness should more than 3mm

 

Condor XC-MINI V4.0.1 update download:

https://mega.nz/#!LghkGQoT!nhs6ucmeVwPj5sov3iI5WK2pVsuTe1PziwASvMbOYtI

(No pass, safe, working)

 

Condor XC-MINI V4.0.1 update procedure:

  1. Connect Xhorse Condor XC-MINI host to the PC with a USB cable.
  2. Turn on Condor XC-MINI.
  3. Click “Update online” button to start update.
  4. The screen will appear “Updating” Prompt.
  5. Wait for the update completed.

Notes:

Do not turn off PC or unplug USB cable during updating.

Data downloaing and firmware upgrading may take a while, please be patient.

If the update fails,turn off anti-virus software and then try again.

condor-mini-communication-error-5

Xhorse Condor XC002, Condor XC-MINI & XC007, which cuter machine recommend?

Here Xhorse Condor cuter machine comparison table which lists the similarities and differences among Condor XC002, Condor XC-MINI and Condor XC007.

With the newly released Xhorse Condor XC002 Mechanical Key Cutting Machine, Xhorse users ask how to choose best Xhorse cuter machines among Condor XC002, Condor XC-MINI and condor XC007? Which one is better? What are the similarities and differences? Here a Condor XC002, Condor XC-MINI & XC007 comparison table.

 

Xhorse Condor cutting machines Condor XC002 Condor XC-MINI Condor XC 007
Quality Made by Xhorse Made by Xhorse Made by Xhorse
Automatically/ Mechanically Mechanically/Manually  Automatically Automatically
Lost key  Not support Support Support
Touch screen  No screen 7″ Capacitive Large screen
Cut car key Yes Yes Yes
Cut house key  Can cut a small part of house key No No
Internal software NO Yes Yes
Language It is mechanical, no specific language Portuguese/Spanish/French/Germany/

Russian/Czech/Arabic/Turkish/Dutch/

Polish/Bulgarian/Norway/Slovakia/Italian/

English/Chinese (English is the default language, after receive the machiche, send SN to seller for reset other language)

English, Chinese
Stand-alone Yes, no need connect to computer Yes, no need connect to computer Yes, no need connect to computer
Input Voltage 220VAC 90V–264VAC AC110V/220V
Input Frequency 50Hz 47~63Hz 47~63Hz
Consume 200W 200W 220W
Packing Dimensions L595*W550*H375mm L450*W450*H350mm L460*W 520*H 620mm
Machine Dimensions L298*W445*H525mm L265*W362*H301mm L336*W 407*H490mm
Display 1024*600 800*480
Spindle Speeds 8000-10000rpm 9000rpm 12,000 rpm
USB USB2.0 USB2.0
Working Temperature 0~50℃ 0~50℃ 0~50℃
Humidity 10~90% 10~90% 10~90%
Net Weight 23Kg 18Kg 31Kg
Gross Weight 28Kg 22.9Kg 35Kg
Price $779 + shipping cost $2,799 free shipping $2,970 free shipping
Warranty 3 years 3 years 3 years

In conclusion

  1. Condor XC007 Master, the first automaticallykey cuter machine from Xhorse Company, is bigger than xc 007 mini. It is not good if you want working on the van, xc007 mini is good if you want use this on the mobile locksmith on the van, both machines can cut the same tape of key.

Condor XC002 [/size] manual key cutting machine works mechanically.

 

  1. Input Voltage:

Condor XC002 input voltage: 220VAC;

XC-MINI input voltage: 90V–264VAC;

Condor XC 007 input voltage: 110V/220VAC

 

  1. Weight: condor xc-007 master series > condor xc-002 > mini condor (lightest)

 

  1. Warranty: all Xhorse Condor cutting machinesare 3 years warranty

 

  1. Cut car key / house key: Condor XC002can cut car keys as well as a small part of house keys; Condor XC007 Master and xc 007 mini can only cut car keys.

 

  1. Language:  Condor XC-MINIis Multilanguage

(Guide) How to use BMW HU92 Turbo Decoder lock pick set?

Here is a detailed user guide for you to use BMW HU92 Turbo Decoder lock pick set. This blog will make you clear all operating steps to do a successful lock picking!

Here is a detailed user guide for you to use BMW HU92 Turbo Decoder lock pick set. This blog will make you clear all operating steps to do a successful lock picking!

bmw-hu92-turbo-decoder-user-guide-1

3 steps to use BMW HU92 Turbo Decoder lock pick set:

Step1. Preparation before unlocking

First make the gate wheel line and turbo wheel line in a straight line as picture show, then pull the gate wheel until you see “STOP” to open the gate wheel.

bmw-hu92-turbo-decoder-user-guide-2

Push the pick (reset tool) against the pins to make them open to maximum position.

bmw-hu92-turbo-decoder-user-guide-3 bmw-hu92-turbo-decoder-user-guide-4

 

Push back the gate wheel to close and turn the turbo wheel line to right maximum position.

Step2. Unlocking

Use the tester key to test which key blade side upwards to unlock the lock. If tester key short side upwards can fully insert in the lock then you should use Turbo Decoder short side upwards to unlock, vice versa.

bmw-hu92-turbo-decoder-user-guide-5 bmw-hu92-turbo-decoder-user-guide-6

 

Holding the gate wheel insert Turbo Decoder HU92 into the lock. After insert decoder open the gate wheel.

bmw-hu92-turbo-decoder-user-guide-7

Turn the tension wheel slowly to right with tension. At the same time turn the turbo wheel maximum to left then turn it back.

bmw-hu92-turbo-decoder-user-guide-8

Repeat several times and juggle a little bit until the lock can be fully open.

Now close the gate wheel (push it back) and turn the turbo wheel line maximum to right. Holding the tension wheel and pull out Turbo Decoder.

Step3. Read the key cutting code and use Condor XC-MINI Key Cutting Machine simply enter the code to cut a new key.

bmw-hu92-turbo-decoder-user-guide-9 bmw-hu92-turbo-decoder-condor-xc-mini-10

 

Why choose Condor XC-MINI Key Cutting Machine? (Review)

In general, with reasonable price and excellent performance Condor XC-MINI Key Cutting Machine is a decent tool! That’s the answer. And below users feedback and reviews can prove it!

In general, with reasonable price and excellent performance Condor XC-MINI Key Cutting Machine is a decent tool! That’s the answer. And below users feedback and reviews can prove it!

condor-xc-mini-master-key-cutting-machine-1

(Tested OK) Condor XC-MINI users’ feedback and review:

  1. Cut New GM, Coverlet, HU100, PSA Peugeot, Citroen VAT2 key, XC-MINI makes job easier
  2. Do Toyota TOY43 all key lost, save you a lot of time
  3. Cut Suzuki, Mazda (key tooth in ignition lock more than door lock) all key lost, simply by enter the key code
  4. Do Hyundai, Kia, Peugeot, and Citroen all key lost, directly program keys
  5. HU101 works fine, HU92 works fine.
  6. HU66 OK, have to do two passes on each side to get the key to work, same with hu100.
  7. Fix the problem that other key cutting machines cut domestic Honda key not accurately
  8. Clio 2 series with m1 clamp all is ok perfect
  9. Panda MJ year 2005 cut key ok
  10. Support “Define key tool” in a short time, for example: define 2015 corolla key

But we have to commit that no tool is perfect! Below are some aspects Condor XC-MINI can improve and be better:

  1. No built-in battery
  2. No solution for Renault emergency blade yet
  3. Condor XC-MINI cannot decode HU83
  4. Track still breaks

For key cutting machine price $3,000 around, Condor XC-MINI Master is the best! Condor XC-MINI Key Cutting Machine will only cost you $2,999! (Package include all tools you need to start key cutting job)

condor-xc-mini-master-key-cutting-machine-2

Condor XC-MINI Master tested OK to cut Toyota TOY48 key blank

It’s tested ok to cut a Toyota TOY48 key blank using iKeycutter CONDOR XC-MINI key cutting machine. Below operating steps will show you how to cut TOY 48 key successfully!

It’s tested ok to cut a Toyota TOY48 key blank using iKeycutter CONDOR XC-MINI key cutting machine. Below operating steps will show you how to cut TOY 48 key successfully!

Click on “Key Database”, enter “Toyota” and confirm

condor-xc-mini-cut-toyota-toy48-key-1 condor-xc-mini-cut-toyota-toy48-key-2

 

Enter key code 46422

condor-xc-mini-cut-toyota-toy48-key-3

Push the M2 clamp with side A upwards and tighten. Put a new TOY48 key blank blade on clamp and tighten.

condor-xc-mini-cut-toyota-toy48-key-4

Click “Cut”

condor-xc-mini-cut-toyota-toy48-key-5

After key cutting stop, turn the other key blank side and click “Cut” to continue.

After the machine stop, key cutting complete. Use brush to clear up clamp. Now a new working Toyota TOY48 key blank is cut easily by CONDOR XC-MINI Master! That’s the complete key cutting procedure. Hope it helps!

condor-xc-mini-cut-toyota-toy48-key-6

How Condor XC-MINI Master cut VW Touareg HU66 key step by step?

Are you looking for a guide for using Condor XC-MINI Master to duplicate VW Touareg HU66 key? This blog will show you step by step!

Are you looking for a guide for using Condor XC-MINI Master to duplicate VW Touareg HU66 key? This blog will show you step by step!

 

Step1. Choose “Key Duplication” function, select “Volkswagen” then “Touareg”.

Condor-xc-mini-cut-VW-Touareg-hu66-key-1 Condor-xc-mini-cut-VW-Touareg-hu66-key-2 Condor-xc-mini-cut-VW-Touareg-hu66-key-3

Choose car type and year

Condor-xc-mini-cut-VW-Touareg-hu66-key-4

Step2. According to the screen key cutting diagram put the M2 clamp with side C upwards.

Condor-xc-mini-cut-VW-Touareg-hu66-key-5 Condor-xc-mini-cut-VW-Touareg-hu66-key-6

 

Put the original VW Touareg HU66 key into M2 clamp then tighten

Condor-xc-mini-cut-VW-Touareg-hu66-key-7

Step3. Click “Key Decode” and “Confirm”

Condor-xc-mini-cut-VW-Touareg-hu66-key-8

After key decoding complete, remove the original key, insert the new blank HU66 key and tighten

Condor-xc-mini-cut-VW-Touareg-hu66-key-9

Step4. Click on “Correcting& Cut” and key cutting start.

Condor-xc-mini-cut-VW-Touareg-hu66-key-10

After one side cutting complete, turn the key blank opposite side upwards to continue cutting, click “Correcting& Cut”.

 

After the machine stop click “Confirm” and the whole HU66 key duplicating process complete. Condor XC-MINI Key Cutting Machine successfully cut a new HU66 key for VW Touareg!

(Guide) How to calibrate Condor XC-MINI M1&M2 clamp?

If you need to know how to calibrate Condor XC-MINI Key Cutting Machine M1 and M2 clamp, this is a step-by-step guide for your reference. Hope it helps!

If you need to know how to calibrate Condor XC-MINI Key Cutting Machine M1 and M2 clamp, this is a step-by-step guide for your reference. Hope it helps!

 

How to calibrate Condor XC-MINI M1 clamp?

Click “Self Test” then “Clamp Calibration”.

condor-xc-mini-m1-m2-clamp-calibration-1 condor-xc-mini-m1-m2-clamp-calibration-2

 

Choose “M1”

condor-xc-mini-m1-m2-clamp-calibration-3

Put a blank key into M1 clamp and tighten.

condor-xc-mini-m1-m2-clamp-calibration-4

Click “Continue”

condor-xc-mini-m1-m2-clamp-calibration-5

After the machine stop, click “Confirm”. Condor XC-MINI M1 clamp calibration complete!

condor-xc-mini-m1-m2-clamp-calibration-6

How to calibrate Condor XC-MINI M2 clamp?

Click “Self Test” then “Clamp Calibration”

Choose “M2”

condor-xc-mini-m1-m2-clamp-calibration-7

Put the M2 clamp with side “A” upwards then click “Continue”

condor-xc-mini-m1-m2-clamp-calibration-8 condor-xc-mini-m1-m2-clamp-calibration-9 condor-xc-mini-m1-m2-clamp-calibration-10

 

After side “A” calibration complete, turn side “B”→ side “C” → side “D” in sequence. Steps are same as side “A” calibration.

After the machine stop, click “Confirm”. Condor XC-MINI Master M2 clamp calibration complete!

condor-xc-mini-m1-m2-clamp-calibration-11